The CAT5 KVM Extender Set is a new KVM extender technology that utilizes CATx media to extend your console up to 100M away. This cost-effective KVM Extender Set not only extends your keyboard, monitor and mouse from your computer up to 100m (330 ft) on a single CAT 5 UTP cable, with satisfying signal quality that suffers no visible loss.

UKE-100-RX & UKE-100-TX Units for Receiver and Transceiver unit

The CAT5 KVM Extender Set comprises two disparate units- The UKE-100-RX and the UKE-100-TX. The UKE-100-RX is the remote console unit, or simply put, the receiver on the one end of the UTP cable; while the UKE-100-TX is the computer module with a local console, or simply put, the transmitter on the other end of the UTP cable. However, the UKE-100-TX also provides a local console, so that user can also access the computer just on the computer end, in addition to the remote console on the UKE-100-RX.

Local Console Hotkeys for Remote Console Access Control

The UKE-100 CAT5 KVM Extender Set provides configuration hotkeys that can be issued on the local console to configure the remote console access control for normal mode or view-only mode as well as the hotkey preceding sequence selection. These hotkey commands are only available on local console (on the UKE-100-TX unit) and not on the remote console since the remote console might be located within non-secured area and access should be restricted. With these hotkeys, users can either block or grant access, or toggle on/off the view-only mode on the remote console. For someone who does need to use different hotkey preceding sequence, it also provides 5 alternatives for choice.  Thus, the Local Console (i.e. the TX unit) will have permanent access of the computer without limitation; the Remote Console can be enabled with full access or view-only access, or access disabled entirely from the local console.

Hotkey selection for DDC/EDID emulation modes – Default / Remote / Local EDID Copy commands

The UKE-100 CAT5 KVM Extender Set also provides extensive support modes for EDID data emulation. Simply by using keyboard hotkey commands (ScrLk-ScrLk-M – 1/2/3), users can designate the EDID emulation to use the EDID data copy from either the default EDID (factory default) or that from the Remote monitor or that from the Local monitor. With these emulation modes for choice, it can directly copy the EDID from the monitor actually in use when the default EDID fails to be compatible with it.

CAT5 KVM Extender technology for flexible computer/user topology

It is especially useful for setting up a highly flexible and at the same time, extended computer/user topology over a long distance up to 100M. Applicable either over an exhibition room, industrial floors, security room, locked server room, or other mission-critical scenarios, the KVM extender set allows you to locate your server physically far back from the user due to security or spatial concerns.

Dual keyboard/mouse interface support for USB and PS/2 on computer side.

The CAT5 KVM Extender Set also provides extension support for both USB and PS/2 keyboard and mouse interface on computer side; while on the console side, it supports physical PS/2 keyboard, mouse and HDB 15 video interface.

Extension up to 100M w/ high resolution

The extension distance is up to 100M with no visible compromise on high video quality..

Mechanical knobs for fine-tuning video parameters

The CAT5 KVM Extender Set is manufactured with a sturdy metal case for robust and reliable usage over years to come. And its deployment is just as simple as can be. Video settings such as gain and equalization can be done by adjusting two mechanical knobs on the front of the receiver unit.
 

▪ CAT5 KVM Extender Set - UKE-100-RX (Receiver Unit) / UKE-100-TX (Transmitter Unit)

▪ Local console hotkeys for remote console access control for normal mode (full access) or view-only mode

▪ USB and PS/2 interface support on computer module side (UKE-100-TX)

▪ PS/2 interface support on console side (UKE-100-RX)

▪ Two mechanical knobs for easy configuration of all settings such as equalization, gain, etc.

▪ DDC/EDID support for 3 modes - Default / Local / Remote EDID Modes – selectable by keyboard hotkeys

▪ Full keyboard & mouse emulation to support Microsoft and Logitech standard 5-key mouse and compatibles

▪ Support for DOS, Windows 95/98/SE/ME/2000/XP/Vista, Linux, Mac OS, Sun Solaris, etc.

▪ Easy Plug-and-Play to extend your second console up to 100M away

▪ High resolution 1600 x 1200